Your cart is empty.
Your cart is empty.
The Buildtak 3D-printing build surface is a 10" x 10" square sheet that adheres to a print bed of a fused-filament 3D printer (sold separately) to help the filament stick during printing, while also enabling clean removal of the printed part afterward. The sheet is compatible with ABS, PLA, HIPS, PET+, brick, wood, and flexible (TPE) filaments (sold separately), and has a durable construction that allows for multiple uses with either the same or different filament material. The build surface can also be used with nylon and t-glase when a thin layer of washable glue stick (sold separately) is spread onto the surface. It installs more quickly and with fewer bubbles than tape or films.
Ideal Jacobs manufactures the Buildtak 3D-printing build surface and provides custom services such as rapid prototyping, laser-cutting, machining, and injection molding. The company, founded in 1921 and headquartered in Maplewood, NJ, meets International Organization for Standardization (ISO) standards 9001:2008 and 14001:2004.
Timothy R.
Reviewed in the United States on July 18, 2022
I mainly print in PLA with various FDM printers.I’ve been using Buildtak for more than 5 years and I haven’t found anything I trust more for adhesion during and removal after the print job.Most if the time I don’t use the heated bed as it doesn’t seem to need it. I’ve stuck the BuildTak to aluminum, glass, and steel all with great results and longevity.If you want a long lasting build surface, this is the ticket. I get 100’s of prints per sheet and this is only my third order in 5+ years.Great product and great value.
Mr. T
Reviewed in Italy on May 13, 2022
I fogli BuildTak sono adesivi e una volta applicati sul vostro piano di stampa garantiscono una adesione perfetta! Lo consiglio a tutti quelli che impazziscono per far aderire il primo strato, magari per chi ha già provato senza succecco lacche e nastri adesivi. Questa è la mia seconda esperianza con questi fogli adesivi, la prima volta l'ho applicato direttamente sul mio piatto in vetro (Artillery Genius) e subito ha risolto ogni problema di aderenza, poi visto che impiegavo troppo per staccare gli oggetti stampati, ho preso un kit magnetico (lamina metallica + pellicola magnetica) su cui ho steso un foglio BuildTak così ho ottenuto aderenza ed accellerato rimozione! PS il mio piatto è più piccolo però per non aspettare troppo ho preso questo kit da 245x254 e dopo ritagliato le parti in eccesso!
Sebastian Schmidt
Reviewed in Germany on August 2, 2021
Sehr gute Druckergebnisse, kein warping o.ä. aus meiner Sicht der beste Allrounder der Druckflächen.
Customer
Reviewed in Canada on November 8, 2019
I have this on my Prusa i3 MK2S, and on both of my i3 MK3Ss. Bed adhesion is phenomenal with the BuildTak surface, have not seen any prints lifting or curling up since I added this on. Printing PLA on it makes it adhere almost too good to the bed for the first several prints until the surface wears down slightly, so if you can't remove your print just heat your bed up to around 80-90C and the prints should pull off at that point.
Jud Niven
Reviewed in Canada on March 20, 2018
Works really well to keep my large PLA prints from warping.
Eric M. Kelly
Reviewed in Canada on September 7, 2017
Cheaper than the lokBuild, you get 3 with this at least and sticks much better. make sure bed is level and calibrate nozzle first. if you get warping, move it closer by 0.01-0.02 mm increments until it's sticks. too much and you'll risk getting prints stuck on it forever. use gcode for this, not the printer. set a negative start (unless your endswitch is in the way...).I use it for ABS/Polycarbonate in a chamber and it's great. i usually throw on a brim so i can easily lift it and get a spatula or floss under the print to pop it off instead of trying ram into the print's bottom layer.
Kithmo
Reviewed in the United Kingdom on January 6, 2017
Marvellous stuff, I was a bit sceptical of all the hype for this stuff until I tried it. Very easy to apply after cutting to size and very durable. Print after print stick to this even printing in the same spot on the bed many times. No more faffing about with masking tape and glue stick, just a wipe now and then with 70% solution Rubbing alcohol and you're good to go again. I've used this first piece for over 20 prints so far and it's not showing any signs of wear at all. Some people think it's a bit expensive but it's well worth the expense to save all the hassle of prints coming off the bed part way through and the constant changing of masking tape and such.
Imbar Samuel
Reviewed in the United States on December 11, 2016
very quality material, sometimes hard to get printed items from itbut this material helped me with the ABS material a lotrecommended!
Recommended Products
