Your cart is empty.
Your cart is empty. NOTE: 1. ESC was soldered with 3.5mm Female banana connectors, effectively avoid welding problems; 2. have set up the Simonk Firmware program.
Brand: QWinOut
Working current: 30A/40A (Optional on my shop)
Output:
30A Version: Continuous 25A, Burst 40A up to 10 Secs
40A Version: Continuous 40A, Burst 55A not down to 10 Secs
Input Voltage:2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery
BEC:5V 3A
Max Speed:210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM.(BLM: BrushLess Motor)
Weight:about 25g
Compatible for:
DIY FPV KK MK MWC RC Quadcopter Hexacopter Multi-Rotor Aircraft;
210 360 450 Helicopter;
380 f450 f550 and other four-axis six-axis fixed-wing drone.
Features
1.Safety Arming Feature: Regardless the throttle stick position, the motor will not spin after battery connected.
2.Throttle Calibration: Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.
3.Programmable Items:Brake Setting:brake enabled/brake disabled. Battery Type:Li-xx(Li-ion or LiPo)/Ni-xx(NiMh or NiCd). Low Voltage Protection Mode(Cutoff Mode):Gradually reduce the output power/Cutoff the output power. Low Voltage Cutoff Protection Threshold (Cutoff Threshold):low/medium/high. Start Mode: normal/soft/very soft. Timing:low/medium/high. Reset: reset all the programmable items to their default settings.
4.Full Protection Features: Low voltage cutoff protection/Over-heat protection/Throttle signal lost protection.
Suggestion:Do a throttle range adjustment before taking off as following steps:
1.Connect ESC/motor/receiver
2.Push the remote control throttle to maximum
3.Connect power
4.Hear the regular sound of D- D- D……, unplug battery
5.Reconnect power and hear DD quickly sound
6.Pull the throttle to minimum
7.D sound once, calibration successful
Orbit
Reviewed in the United States on August 12, 2024
Good power source.
Rod Fuller
Reviewed in the United States on November 24, 2022
I have been through four of these now, and don’t ask me why I have ordered so many after having so much trouble! Two of them burned out for no apparent reason, likely they are way overrated by their amperage. The other two caused some type of voltage transient, resulting in multiple plane crashes. The whole time I suspected faulty receivers, servos, etc.. After changing them all out and still dealing with the same problem, I switched out ESC’s. Miraculously, no problems! I don’t know how an ESC can cause so many issues, but between the interference and the outright failures, I am zero for four, and many, many lost hours trying to troubleshoot. I can’t steer you away from this product strongly enough!
CODY
Reviewed in Canada on April 17, 2022
I am going to go out on a limb and say these are highly over rated in the actual amps they can handle.
Otterblast
Reviewed in the United States on August 8, 2021
So when I first tried to use these they wouldn't work at all. My main problem turned out to be not having a common ground because I had different power sources for my Arduino controller and the ESC's/Motors. They all work great and don't seem to have any heating issues yet.Used with 935kv motors and 3S battery, working well so farFOR CALLIBRATING:1. Have motor/reciever sending data2. Throttle up to full3. Power the ESC/Motor3. You should hear 3 D's (means getting power) followed by 1 D (means getting HIGH signal)4. Lower throttle to the minimum5. You should hear 2 D's -- after that you should be good to throttle up
Ben
Reviewed in Canada on November 1, 2021
They seem to work ok, however, one unit was dead on arrival.
Franz
Reviewed in Germany on June 26, 2020
schnelle Lieferung, alles OK, Danke
Luca
Reviewed in Germany on November 8, 2019
funktioniert und kam früher als angegeben
Recommended Products
$18.50
$ 9 .35 $9.35