Your cart is empty.
Your cart is empty. #801 Gray Dektite Retrofit EPDM Flexible Pipe Flashing (RF801G)
-Flashing Base Diameter is 6-1/3" - Pipe Boot Fits 3/4" to 2-3/4" Outside Pipe Diameter
-Continuous Service Temperature Ranges of -58F to 239 F (EPDM)
-Easily Customize Pipe Boot Size on the Job Site With Shears or Heavy Scissors
-EPDM Rubber Boot with Flexible Base (Aluminum Collar) Seals Against Uneven Metal Roofing Easily
-Fasten Aluminum Collar To Metal Roof With Metal Roofing Screws Every 1-1/2"
-Where the Height of Pipe is Difficult to Reach or Existing Obstruction Blocks Top of Pipe;
-Flashing Can Be Cut Along the Seam and Resealed With Provided Clips
-If Trimmed and Installed Correctly, Pipe Flashing Will Not Break or Crack
-Reduces Building Maintenance Due To The Long Life of the Dektite Product
-Use for Stove Pipes, Chimneys, Plumbing, Heating, Air Conditioning, Electrical, and Exhaust Vents
-20 Year Manufacturer's Warranty Against Manufacturing Defects
Works with Metal Roof Pitches up to 10/12 (0 to 40 degrees)
On a Roof with a 10/12 to 12/12 Pitch (40 Degrees) Dektite Recommends You Use a Square Base Pipe Flashing Installed With The Base Tip Pointed Towards Roof Top. When Used With Deep Ribbed Profile Roofing Panels With 1-1/2" Deep Corrugation Or More, Consider Using Next Size Up That Will Accommodate The Same Diameter Pipe
Caution: This product is not rated for temperatures experienced by prolonged contact with a single wall chimney. Manufacturers Recommended Temperature Ranges Are Clearly Stated. Please Verify This Product Will Meet Specifications Of Your Installation Or Possible Product Damage May Occur
For single wall chimney applications consider using a High Temperature Silicone Flashing product that is rated for high temperature applications
mike
Reviewed in Canada on September 7, 2024
At first I thought it was a bit expensive but I can see why, it is solid and very well made, worked great!
David Miller
Reviewed in the United States on September 24, 2024
It was very easy to modify and fit over the vent pipe. You still need the self tapping screws and silicon sealer. I recommend viewing the video before you begin the installation if you haven't done this before.
DS
Reviewed in the United States on May 1, 2024
Nice, well made boot. A bit pricey, but since it's a "zip up" I didn't have to kill the power going into my house to seal the riser pipe through the roof. The "zipper" can be a bit of a handful while working on a sloping roof, but I'm pleased.
A. Cooper
Reviewed in Canada on November 3, 2024
I bought this for my electricity service stack on my house. I was able to split the boot and put it on the stack after cutting the top to the desired size for the stack. The rubber compound was very pliable yet tough. I had to use sidecutters to cut the top off the boot. (which is a good thing). I found the base to be a little smaller than I expected but it is also a smaller boot.
alease s. copelin
Reviewed in the United States on January 17, 2024
Easy to install and fit great. Great purchase and I did not have to wander around Walmart or a hardware store to find it!
Customer
Reviewed in the United States on August 24, 2023
replacing roof flashing this is a great upgrade. Prepping the surface is a must, clean & remove all old caulk
Tyler
Reviewed in the United States on November 8, 2023
I used it on a metal roof for a Electrical Mast and it worked great just make sure your cuts small. No room for error. But it's very low profile and looks good.
Lafleur
Reviewed in Canada on July 13, 2022
Bonne description et bonne qualité du produit
Gabor M.
Reviewed in Canada on November 1, 2022
Great product, but pricy for a small piece of vinyl..
Recommended Products
$32.44
$ 16 .59 $16.59
$843.16
$ 74 .69 $74.69