Your cart is empty.
Your cart is empty.Protect the engine, the engine components and the engine hoses with Dorman's Undercar Splash Shield. It safeguards against corrosion by preventing salt, water, and snow from splashing up into the engine.
Garry
Reviewed in Canada on October 26, 2024
Part was designed very well. All holes lined up.
Eddie
Reviewed in Canada on January 7, 2024
The shield fits in the proper mounting holes but the oil filter access hole is in the wrong place for a 2007 Mazda 5. I did not figure this out until I installed the shield and destroyed the packing box.
felyan
Reviewed in Canada on July 9, 2023
The screws this splash shield comes with really helped me replaced the rusted ones. The shield also fits perfect on my Mazda 3 2008!
Customer
Reviewed in Canada on February 6, 2021
The skid plate fits perfect much stronger material than the original only issue is the hole for the oil filter is in the wrong spot but still dose it’s job
Klinsmann Gómez López
Reviewed in Mexico on November 25, 2021
Excelente calidad y se ajusta perfecto al auto mazda 3 sedan 2007
William H.
Reviewed in the United States on September 8, 2020
I've purchased this part a few times over the years. I seem to manage to hit road-going animals every few years which tends to break this shield. The part is inexpensive, high quality, and includes the clips and screws for all but the front 3 screw locations. I've put 250k miles on this car in the 10 years that I've had it and the underside of the engine still looks great. I can't help but believe that keeping a splash guard in place has been a large part of that.
JettaGLIg60
Reviewed in Canada on February 8, 2020
solid part, fits great and easy to install BUT bought this for my 2008 Mazda 3 GT, there is a hole in the belly pan so that you can access the oil filter. This belly pan has the hole in the wrong spot (at least for my car), but it does fit really well and installs easy, just a pain that you must remove the belly pan when you do oil changes.
Al C
Reviewed in Canada on October 4, 2020
Just finished installing on my daughters car (2008 Mazda 3 GT). Fits perfectly, made of high quality materials. Very easy to install, The hardest part is removing the old broken one with rusted out bolts. and the only modification I did was cut out a circle to access the oil filter, so when I take it in for an oil change they don't have to remove the whole thing again. Highly recommended.
Be Money
Reviewed in the United States on August 7, 2019
I didn't have any issues with warping. Typically, any car part that you replace takes a little elbow grease to get the fitment/bolt alignment right. If you want to ease somebody into DIY car repair, this would be the starter project to complete their first oil change.It will also make future oil changes and DIY car work much easier...and clean if your car has 110,000 miles on it like mine did when I picked it up. After doing a few things under my car I realized that the most annoying part of every project was taking off and replacing the sagging, cheap, annoying (seriously!?), stock splash guard.The oil filter hole isn't aligned with the actual oil filter, but it didn't align on the stock guard either. I'll probably mark off the filter location during the next oil change and cut out the area so I don't have to remove the entire shield in the future. It's nice to know I have 5 minutes to complete a simple step instead of 15 minutes of cursing everything on the earth to get a stupid splash guard off...or on.Great value.
Jesse Simon
Reviewed in Canada on May 13, 2019
Bought this to replace the splash shield that came off my 2004 Mazda 3. Fit pefectly with no issues. Easy to install, and inexpensive. Better quality that the factory splash shield.
Cstew73
Reviewed in Canada on October 17, 2019
Just installed it this week, but it fit very well (2008 Mazda 3). Just a bit of elbow grease required to get everything lined up. Seems durable. As others mention, the hole on the bottom doesnt line up with the oil filter, but the original didn't either.
SSD
Reviewed in the United States on November 19, 2018
This shield, despite the few less than enthusiastic reviews here on this site, is a well made part which fit my car (2004 Mazda 3s) perfectly. The shield is very sturdy, came in nearly flat (not warped) and nearly mimics the original shield in all respects (which, in fact, is not a good thing because the round cutout for allowing to change the oil filter is still not aligned with the filter but the hole is actually closer to the filter than on the original shield.) Comes with the necessary hardware (nuts/clips and screws). Considering the price of an OEM shield, this is an exceptional buy - 5 star.
Mr K A Baldwin
Reviewed in the United Kingdom on February 5, 2016
The panel was a little warped and oil filter hole is on wrong side.The fittings had torn through the plastic bag and became loose in box. One fixing bolt was missing as a result. Easy to fit however.
Recommended Products
$165.59
$ 71 .28 $71.28