Shopping Cart

Your cart is empty.

Your cart is empty.

SJ@JX 2 Player LED Arcade USB Encoder Board Zero Delay Game Controller Light DIY Kit 20x Button Cable 2X Joystick Cable for Retro Pie PC MAME Raspberry Pi

Free shipping on orders over CA $49.99

CA $34.99

CA $ 16 .99 CA $16.99

In Stock

1.ColourName:Blue



About this item

  • LED Support Zero Delay SJ@JX 2121 USB Encoder for 2 Player Retro Pie Raspberry Pi & PC.
  • Easy To Install Colorful Plugs, White for LED Buttons, Blue for Joystick, Red for Power and USB.
  • SANWA Style: The Button Terminal is 2.8mm, 5pin Joy Cable. HAPP Style: Button and Joy 4.8mm, LED 6.8mm.
  • Encoder Size 9.5cm x 3.5cm x 1cm, USB Cable 180cm, Button & Joystick Cable 35cm.
  • HAPP Include: 1x Encoder, 8x Joystick Cable, 20x Button Cable, 1x USB Cable.


I have listed most of the parameters,

If you have other questions, please contact me by email.

LED Support Zero Delay SJ@JX 2121 USB Encoder for 2 Player Retro Pie Raspberry Pi & PC.

Easy To Install Colorful Plugs, White for LED Buttons, Blue for Joystick, Red for Power and USB.

SANWA Style: The Button Terminal is 2.8mm, 5pin Joy Cable. HAPP Style: Button and Joy 4.8mm, LED 6.8mm.

Encoder Size 9.5cm x 3.5cm x 1cm, USB Cable 180cm, Button & Joystick Cable 35cm.

SANWA Include:

1x Encoder,

2x Joystick Cable,

20x Button Cable,

1x USB Cable.

HAPP Include:

1x Encoder,

8x Joystick Cable,

20x Button Cable,

1x USB Cable.


Foto F.
Reviewed in Germany on February 14, 2022
New product, looking old and used, although it arrived unopened in the packaging.
Ogredude
Reviewed in the United States on February 9, 2021
A few of the wires were too short, but then again I've got a monster of a large arcade controller.It went in easily once I rebuilt a couple of the wire harnesses, and fired up right away in RetroPie as a single-player controller. With a quick config change, two-player mode was enabled, and works great.Note that to enable two-player with this board in RetroPie, you should follow the instructions in the RetroPie documentation for the Xin-Mo controller.
Customer
Reviewed in the United States on January 25, 2021
Does it’s job, I just wish it came with 5pin joystick cables.
TK421
Reviewed in the United States on December 26, 2020
Didn't work for me. I tried everything to get this to work with my raspberry pi. It would only show up as one controller. After hours of of checking my wiring and settings I decided to buy a i-pac2 encoder. Problem solved everything works fine now. Maybe I just got a bad one. I wasn't going to try it again.
JLiev
Reviewed in Mexico on April 3, 2020
El producto funciona perfectamente si lo ocupas para conectar un joystick a la PC, pero si lo quieres para un retro pie, sera mejor que compres 2 tarjetas (1 por jugador). Es un batallar con cualquier imagen de retropie y nunca pude hacerlo funcionar bien.
Recommended Products

CA $14.39

CA $ 7 .99 CA $7.99

5.0
Select Option

CA $1,457.24

CA $ 99 .00 CA $99.00

4.3
Select Option

CA $21.91

CA $ 8 .99 CA $8.99

4.8
Select Option

CA $12.39

CA $ 5 .99 CA $5.99

5.0
Select Option

CA $59.89

CA $ 26 .99 CA $26.99

4.5
Select Option