Your cart is empty.
Your cart is empty.Product Description
Product Introduction
SSR Single Solid State Relay
- Current : 40A
- Frequency : 50/60Hz
- output Voltage : 24-480vac
- Control Voltage : 3-32vdc
- mounting hole diameter : 4.5Mm/0.18"
- Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t)
K-Type Thermocouple Temperature Sensor
- Measuring Range: 0~400°F
- Probe Length: 6mmx20mm/0.23“x0.79“（D * L）
- Terminal: 2 Insulated forks; Thread:2 Meters
- Internal Insulation: Fibreglass; External Shielding: Metal Shield;Thread ： 1/4"
Aluminum Heat Sink
- Material: Aluminum; Color: White
- Applies to: Single Phase Solid State Relays 10A,25A,40A
- Radiator size (approx.): 80mmx 50mmx 50mm/3.1" x2.0" x2.0" (L*W*H)
- Heat sink and solid state relay in this product will be coated with thermal grease and installed properly.
Panel Description
- Front Panel Dimension: 51mm X 51mm/2"X2"(W*L)
- Hole Size：46mm X 46mm/1.8"x1.8"(W*L)
- Power Supply Voltage: 85-265VAC 50/60Hz
- Life expectancy of Relay: Mechanical≥10,000,000 operations Electrical≥10,000,000 operations
- Weight: Approx. 110g
Wide Application
The temperature controller is widely used and is suitable for various occasions such as industrial manufacturing, chemical research, home appliance maintenance, etc.
Camil Rivest Jr.
Reviewed in Canada on February 26, 2025
Efficace pour contrôler les températures de vos besoins, très polyvalent
Charles W. Lipp
Reviewed in the United States on September 9, 2024
Works perfectly. Good instructions for connecting wiring. My system is not so easy to control. Works out of the box with no tuning.
escorpion
Reviewed in Canada on November 17, 2024
precise and tough
Shinku
Reviewed in Canada on March 6, 2023
too late to return, unit has been assembled into a 3D printed enclosure. 12 hour for nothingambient temperature reads wildly my room is not -5c once you give it a little warmth the thermal reading starts to climb rapidly. using my own body I measured the temp reading... I am not 120c.
BV
Reviewed in Canada on February 14, 2023
Works excellent for controlling my paint curing oven. Took a bit of playing around to get the SSR to trigger. I followed the wiring instructions but I couldn't get it to trigger the relay. I applied 12V DC from a DC power supply to test it, triggered the relay just fine. After that, it worked just fine with the PID controller. I think maybe the relay was just stuck and PID controller wasn't putting out enough power to unstick it.
Justin Zimmerman
Reviewed in the United States on April 13, 2022
I used this controller to control my tempering oven for knife making. At first it worked perfectly, showing the same ambient temp as my room thermometer. I was able to temper one knife with two 3 hour cycles at 400F. During the second cycle of the second knife, so fourth use, the controller stopped regulating the temp and now shows ambient temp of 285F. I changed the thermocouple in case that was the issue but still getting same extreme readings. I tried adjusting SC to correct for the difference but no change. Setting AT to yes had no effect. I can set SV to 600F and PV will get there, but the internal temp measured 430F. I can't find anything useful on line to troubleshoot this apparently defective unit. And of course I am beyond the replacement period so a waste of money for me.
John C.
Reviewed in the United States on June 2, 2021
Controller worked great. Word of caution though, don't follow the wiring diagram on the included instruction sheet, it will render your device useless! Follow the diagram on the sticker on the unit. Voice of experience speaking.
rleetay
Reviewed in the United States on July 16, 2020
Like its operation. But, control accuracy is way off. Set Menu 1, SC for correct indication at 200 degrees. Confirmed by IR reader & separate digital thermometer. Then set 300 degrees, measured 349! Then tried set 400 degrees, measured 496! Not good enough! Convection oven, after 1 hour+ at temperature. Separate sensor placed in aluminum block.
Bach911
Reviewed in the United States on November 6, 2020
I spent hundred of dollars on two controllers that work well from an American company that probably out sources manufacturing to China. When I needed two more controllers, I decided to look to Amazon. I have two of these each driving two 700 watt cartridge heaters in two 2X12X12 aluminum platens in my heating press. Their PID works great. I placed each relay on the inside front of the boxes of aluminum for cooling. I remove the cooling fins that came with the relays. The front of the box hardly gets warm. That is 1400 watts for each relay. Great product. Will buy here if needed again.
Recommended Products