Your cart is empty.
Your cart is empty.Product Description
Use Introduction:
1.Pull out the dead point on the stem, close the valve on the tool, adjust the joint of the tool to the air conditioning interface, and tighten the valve on the air conditioning.
2.Make sure that the tool is connected tightly to the air conditioning valve, then open the valve on the tool. Push the stem into the air conditioning valve and gently rotate the tail knob of the remover. Find the angle to connect the valve core, and then loosen it.
3.When the valve core is removed, pull out the stem, close the valve on the valve remover, loosen the screw at the end of the tool and take out the valve core. The work is done!
Feature:
Brand new
Has a ball valve that can be opened and closed in just a quarter-turn rather than a stem-type valve.
Remove and install the valve core without the loss of refrigerant.
Remove valve cores quickly and easily.
High strength and hardness.
Durable in use.
Work on service valves cores of booth 1/4" and 5/16" service ports.
Package included:
1 1/4" and 5/16" Valve Core Remover 1 R410 varied diameter device 4 valve cores
Item Weight:7.41 ounces
Package Dimensions:7.2 x 4.5 x 1.9 inches
Warning:
We suggest that before removing the valve core, close the valve core wrench valve and disconnect the air conditioner internal connection.
Note:
Item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same.
More Detail
The valve body is molded once, which effectively avoids the trouble of leaking the joints of various components caused by multiple moldings.
External bypass design.increase hand friction, prevent all kinds of overpowered valves; High-quality craftsmanship probes, rugged and durable,ergonomically design and optimal force-transmission.
Great quality: The valve core remover is made of thicker brass resisting oil and abrasion.
High-quality craftsmanship probes, rugged and durable, suitable for most equipment.
George Miller
Reviewed in the United States on January 13, 2025
Good value, delivered quickly.
AW2222
Reviewed in the United States on May 23, 2024
I bought two of these as a backup to my Appion version of the same tool and I have to say I am very impressed with the value that this WADEO brand brings to the table. They functioned just as well as my Appion with no leaks or issues removing valve cores and using the included tee for a pressure gauge. Even better, having three of them means that the third one can be used as an inexpensive Y connection to the high and low sides for recovery of refrigerant. I paid 3x for my Appion and while I do not regret having made that purchase this tool is worth every penny. 5/5 stars!
Dustin
Reviewed in Canada on February 9, 2024
From s professional, Don’t waste your time. Absolute garbage.
Customer
Reviewed in Canada on February 24, 2024
Came complete as shown.
Matthew O'Connell
Reviewed in the United States on December 11, 2024
I was hesitant to buy these because they are so cheap, but for a single project didn't feel the need to purchase $70+ name brand ones. Worked perfectly for my mini split install. I pressure tested to 475 psi, then pulled a vacuum. This tool successfully removed and reinstalled the valve stem, as well as held both pressure and vacuum for an extended duration test. Lower quality control means they might make a few with defects, but they allow returns. I am keeping these for any future needs and would not be concerned using them several more times. If I was a professional using them daily or multiply times per week/month, I would invest in higher quality but for the DIYer only needing them a few times, you can't beat the price.
Matthew Power
Reviewed in Canada on September 14, 2023
Works as intended, allows for easy changing of the valve without letting out all the compressed gas/air.Feels a little light on the quality but it does what it needs to do.
jeromef
Reviewed in Canada on June 13, 2023
My navac, the seal broke ...Yellow jacket you need to put 2 adapters...And this one for the price is working as intended. Soap it all and it working great. Cheap alternative. Does the trick for me. Will buy moreDont get me wrong apion is good but this is a fraction of the price even if the seals fail or it starts to leak, ill just replace it
Gene
Reviewed in Canada on May 1, 2022
this is well made but only comes with threaded attachments. I have 4 vehicles and all have Schrader valves on the A/C. This tool does not work on schrader valves and is of no use for most A/C units.
Mkpirulo
Reviewed in the United States on August 6, 2021
This item came very fast, thanks.When I went to use it I could not get the schrader valve into the section that would allow me to turn the ball valve off. It turns out that the internal seals did not allow the schrader valve to pass all the way through the ball valve. The fix for this is to use a drill bit slightly smaller than the inside diameter to remove the encroaching seal material.Using this tool without fixing with a drill bit will put you at danger of losing all of your refrigerant, very expensive issue.Now it works great. Hope that the supplier reads this.Thanks for a cost effective product but please fix at your end before shipment.Mike
Nick
Reviewed in Canada on January 31, 2021
The core remover works quite well, sadly the ball valve was stuck when the unit arrived and the plastic lever snapped off. I now use channel locks to open and close the ball valve. I still think it’s worth the price and will probably buy another one when I get annoyed with the channel locks.
Motrin
Reviewed in Canada on January 30, 2021
Empli commercial
Rich Scheller
Reviewed in Canada on January 25, 2021
Good quality product.
DagDerNiT
Reviewed in the United States on September 2, 2019
The schrader valve remover tool is hefty and looks to be mainly made of brass. Does not come with instructions, but there are many videos if you need to learn how to use it. My York Heat Pump developed a slow schrader valve leak that a soap test revealed last week. Ordered this tool to do the job but unfortunately, the end part of the tool that grabs the valve to remove, didn't grab it firmly, so after completely loosening and pulling out the section to exchange the bad valve for a new one, there was nothing there and just freon blowing out. I tryed to close it off but the stuck valve inside would not let me as it jammed itself sideways. Quickly removed tool and was able to screw a new valve in without losing too much refridgerant (added approximately 2 pounds after sealer-dryer) A/C is ice cold and back in business!
Recommended Products