Shopping Cart

Your cart is empty.

Your cart is empty.

224 Silicone O-Ring, 70A Durometer, Red, 1-3/4' ID, 2' OD, 1/8' Width (Pack of 10)

Free shipping on orders over CA $49.99

CA $12.20

CA $ 6 .99 CA $6.99

In Stock

About this item

  • Made of silicone for use with a variety of chemicals and fluids
  • Can be used across a wide temperature range from-65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
  • Round in cross-section to provide a seal between cylindrical overlapping surfaces
  • Durometer (hardness) of 70A for resistance to penetration
  • Meets standards defined by Aerospace Standard AS568A


This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications. Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.


Randall J. Lovvorn
Reviewed in the United States on April 8, 2025
Perfect fit for my Pentair FNS 48 drain plug. For half the cost of a pool store I now have ten o rings - Thank you!
Jeff's
Reviewed in the United States on August 1, 2024
It fit just right for the seal on the pump sprayer. The original O ring was all cracked and rotted after only 3 months of use, even though I rinsed it thoroughly after each use.
pat
Reviewed in Canada on October 24, 2024
These orings are advertised as ⅛" (0.125") thick. they are actually 0.139" thick, which may work in some cases but it is not what the ad says and not what i need.
Jr.
Reviewed in the United States on January 30, 2024
I purchased a few different sizes for a project almost a year ago. Tight seal, no leaks, did not break when I expanded them, all good.
Robert W
Reviewed in the United States on July 4, 2023
I needed replacement O rings for two Hudson garden sprayers. These were a perfect fit and work very well.
Ed Sadoway
Reviewed in Canada on January 30, 2023
Item recieved as described,very good price
J. Hodgson
Reviewed in the United States on October 20, 2016
Works well does what it need it to do. I am using this o-ring in a very different purpose than it was intended for but it does exactly what I need it to do. Looks like it is dimensionally correct and meets all of its specifications.If I was using it to create a seal I would expect it to be functionally perfect.
Recommended Products

CA $60.29

CA $ 24 .99 CA $24.99

4.3
Select Option

CA $17.47

CA $ 7 .99 CA $7.99

4.3
Select Option

CA $10.99

CA $ 5 .99 CA $5.99

4.8
Select Option

CA $11.74

CA $ 4 .99 CA $4.99

4.6
Select Option

CA $94.39

CA $ 43 .99 CA $43.99

4.8
Select Option