Your cart is empty.
Your cart is empty.Product Description
Which build plate is right for you?
GSI: Grip Strength Index (Rated form worst to best on a scale form 1-10)
Brim Sstting recommendation
- 1-6 (OK adhesion) : Highly recommended to use brim
- 7-8 (Good adhesion) : Brim not needed, But if your print is particularly hard to print, use brim to improve adhesion. If only odd corners are lifting, use mouse ear pads on the corner
- 9-10 (Extremely Good adhesion) : Do Not Use Brim unless your part is extremely small or prone to warping; single-layer brim will be hard to clean off of the plate
Filament Compatibility Chart
- HT: Heatbed Temperature
FMRT: Filament Manufacturer Recommended Heatbed Temperature AFMRT: May require temperatures Above Filament Manufacturer Recommended Heatbed Temperature
- AAR: Adhesion Aid Reccomendation
NAR: No Adhesive Required MRA: May Require Adhesive depending on filament
AR: Adhesive Reccomended
G Ragib
Reviewed in Canada on March 29, 2025
It's a great plate. I like the subtle texture. Always use glue. PLA and PETG stick just a bit too well and you will destroy the plate when removing prints if you do not use glue.
Riggsy
Reviewed in Canada on March 22, 2025
So far all my prints have worked beautifully with this sheet especially on the textured side. Sticks well and stays in place you can feel it after a fresh finished print. I have used the diamond side once and while it printed nicely I’ll have to tweak the settings as there was minor flaws but that’s probably my fault. Overall very happy with this plate and I’ll get more.
D Toronto
Reviewed in Canada on March 15, 2025
I wish I got this sooner. I was having problems with PETG sticking too well. This plate said 8/10 for PETG and PLA. Everything prints great and it's very easy to remove afterwards. So far I have used PETG, TPU and PA6, zero warping. I don't think I'd buy another PEI plate after using this one (Bambu P1S)
Christian Huard
Reviewed in Canada on February 12, 2025
I had lot of troubles with PLA on both the textured PEI textured plate that came with my Ender 3 S1 Pro and the smooth PEI plate.I've been using the BIQU one for a month and despite looking quite dirty, everything still stick to it. After cooling down, the parts come off super easily.The only downside is that I had to remove the 2 screws at the back of the bed that are used to align the plates, since they're not at the right spot. Not a big deal, I simply printed some corner pieces to guide the plate to the right place.
Oseriduun
Reviewed in Canada on January 7, 2025
Title says it all, this is the best build plate I've used across any printer. No adhesion issues, prints come off with a quick bend and a satisfying pop. First layer texture takes a little getting used to but I would definitely buy this again. I might even grab the glacier plate to expand my cold plate collection.
Dave Cruickshank
Reviewed in Canada on December 2, 2024
My first print on this plate was a fail (print lifted off the bed)... I realized that after hundreds of successful prints on my PEI bed... What do I need a blue, cold bed for? There's only a 20 degree difference in recommended temperature between this and PEI. No real benefit. Returned.
Andrei
Reviewed in Canada on October 23, 2024
I found it as a very helpful upgrade. PLA and ABS adhere good. First layer is smooth and neat. It is difficult to level the table because the steel sheet is flexible and not ideal.
Jonas Berntsson
Reviewed in Sweden on June 15, 2023
PETG sticks almost as good on this as on the smooth PEI sheet I normally use...but is getting a bit worn. Thin and both sides are coated. I like it!
SEBASTIAN
Reviewed in Spain on May 22, 2023
Me funciona muy bien y fácil de instalar, lo mejor que puedes poner de cama
C Jackson
Reviewed in the United Kingdom on April 19, 2023
This steel bed is a lot more flexible than the one that came with my Creality Ender 5 S1. However, the magnets work and is sticks to the heater plate with no issues.I did a quick manual bed level on the corners, adjusted the Z axis offset and set it printing. Adhesion appears good, so looks very promising.This plate does not have locating notches (unique to the Ender 5 S1), but that is a non-issue. Time will tell how long the surface lasts, but it is double sidedAll in all, a good replacement if you damage the bed that came with your printer. Cheap, good adhesion and the flexibility makes removing your prints easier.
Ben Surinx
Reviewed in the Netherlands on September 27, 2022
Beste 3D printplaat die ik ken, ik heb deze ook voor mijn Ender 3 Max en Balco 3D printer.Snelle levering.Super tevrede.
ARK
Reviewed in the Netherlands on March 19, 2022
Dit product is echt een aanrader!Ik gebruik veel PETG filament wat niet altijd even makkelijk is om mee te werken. Voor dit materiaal is een goede instelling van je printer essentieel met een goede bildplateIk heb diverse merken geprobeerd maar deze bildplate springt er voor mij als beste bovenuitGeen lijm nodig en toch een goede hechting bij het printen ( ook bij kleinere oppervlaktes)Na het printen even de bildplate buigen en het ontwerp springt ervan af,,, even met een doekje en wat alcohol schoonmaken en de plaat is weer als nieuw
JAMES GYOBA
Reviewed in Canada on October 16, 2021
So the good.The magnetic sheet is easy to apply and sticks down to the heated bed nicely. It's a good uniform thickness, and holds the build surface securely.The prints do come off of the build surface cleanly and easily.The bad? They come off while it's still printing.I could sort of get PLA to stick with the bed at 135°C. that was the only way to get a print more than 2mm tall. It still didn't finish my 55mm tall model before coming off by itself. I do the vast majority of my printing in PETg, which I could not get to adhere to the bed at all. Not even 1mm before it started sliding around with the print head.In short, it's a 310mm by 320mm piece of trash. I'll be throwing it away,
Recommended Products