Your cart is empty.
Your cart is empty.Husky Mud Guards are a perfect match for your fender; more than a match for anything the road kicks up. Delivering nail-tough protection for your truck, van, or SUV thanks to its thermoplastic construction. Engineered for the ultimate in impact resistance, plus, the added invincibility of Husky Shield for an extra layer of defense for your vehicle’s paint. Available in single or dually factory-tire width. Proudly made in the USA, guaranteed for life—like all Husky products.
Yvonne
Reviewed in Canada on March 5, 2025
Easy to intall. Look great
Alfred Kelly
Reviewed in the United States on March 4, 2025
Great addition to my F-250 king ranch. Easy to install and great fit. Very happy with this product.
jim webb
Reviewed in the United States on March 23, 2025
Good fit easy install
Rick Yandle
Reviewed in the United States on March 16, 2025
Perfect fit on my 2024 F350 Superduty. Easy to install and they look great.
Darren
Reviewed in Canada on February 2, 2025
Nice product
jeff kurz
Reviewed in the United States on January 12, 2025
FRONT FLAPS: Had to trim OE Rock guards inside corner about 1/8 of an inch to get mud flaps to seat properly. Used OE clips on felt guard with provided longer screws to tighten everything together.REAR WELLS: fairly simple to install, installed mud flap clips prior putting wells in, (so everything could be tighten together) used a heat gun to make hard plastic a little more pliable (cold weather install).HINT: installed mud flap clips on plasitic wells prior to putting in.REAR FLAPS: fairly simple to install, had already put clips on plastic wells so just a matter of aligning and tightening everything up.
Paul
Reviewed in the United States on April 14, 2025
And the holes lined up but……I could use none of the supplied fasteners. The rear had plastic trim fasteners on the truck that had to be replaced. The front had machine screws but the supplied machine screws were way too short. I tried to match the plastic trim bolts at Auto Zone but there are far too many offered and the ones I bought were slightly too large. A trip to Home Depot for the correct bolts and nuts for the rear in place of plastic trim bolts and 2” #8 machine screws for the front solved the problem. It took 90 minutes to figure out what I needed go get them and a hour to install all 4 once I had the correct materials.
B Dog
Reviewed in Canada on July 12, 2024
They fit the truck perfectly and there were no issues with installation. I question how long the tape fastener is going to last but time will tell. If I have any issues with the tape I will advise you.
ISFINC.
Reviewed in Canada on November 2, 2024
Front and rear fit perfectly. I did not use the 3m paint protection film, it was not cut deep enough to come off in its shape, and I got finger prints on it. So I decided the heck with it. On the front I used the #10 screws in stock locations as the stock screws were not long enough. Then I used the stock screws for optional bolting locations. Used a stubby screw driver on back for the 2 screws in stock holes instead of removing wheels. Took me a couple hours, but I’m slow. Think the paint protection film would take that long, that process just seemed like a pia.
Dennis Harwood
Reviewed in Canada on November 12, 2024
Great products. Fit truck perfectlyb
Jason
Reviewed in Canada on March 6, 2022
Ask expected fit and finish are 100%
mark iula
Reviewed in Canada on August 18, 2019
The mud guards were easy to install and at a great value
Kevin K. Leung
Reviewed in Canada on October 11, 2019
Quality looks good. Cheaper than weather tech. Simple install. The one screws do work they may need some help with a screw driver behind the fender well the help the screw bite due to the extra thickness of the new mud flap. Other than. That a simple job. Would take about 30mins for all 4.
Recommended Products
