Shopping Cart

Your cart is empty.

Your cart is empty.

RUXIFEY Single Side 3rd Third Brake Light Gasket Seal Compatible with Silverado GMC Sierra 1500 2500 3500 2007 to 2013 High Mount Stop Lamp Assembly 2nd Gen

Free shipping on orders over $29.99

$10.29

$ 5 .75 $5.75

In Stock

1.Size:1999 To 2006


About this item

  • COMPATIBILITY: 2007 to 2013 Chevy Silverado 1500 2500 3500; 2007-2013 GMC Sierra 1500 2500 3500; 2007-2014 Chevy Silverado 2500 HD 3500 HD; 2007-2014 GMC Sierra 2500 HD 3500 HD; NOT for 2007 Classic model
  • STOP WATER FROM LEAKING: Replacement and upgrade for the worn out third brake light seal gasket. made of high density, thicker and firmer foam, prevent water from leaking inside of the cab. A great solution for stopping the third brake light leaking
  • SINGLE-SIDED ADHESIVE: Compared to double-sided adhesive gasket, this high quality third brake light seal is much easier to remove the lamp housing to replace burnt out bulb. Easy to peel off and make the light stay in place, no weather strip adhesive needed
  • NOTICE: 0.2 inch (5 mm) thick foam gasket will leave about 1/8 inch gap outside between the housing edge and vehicle body after installed, but it won't affect waterproof function for protecting the inside part. Make sure you understand and accept this design before ordering
  • PACKAGE INCLUDES: 2 x 3rd brake light gasket;



Product Description

The gasket specially designed for third brake light is thicker than original one and make better performance on waterproof. Single-side adhesive, if you want to replace a burnt out bulb, it is easy to remove the light assembly and won't ruin the gasket. check compatibility table before ordering

Package Includes:

2 x 3rd brake light gasket

Compatibility:

2007-2013 Chevy Silverado 1500 2500 3500

2007-2013 GMC Sierra 1500 2500 3500

2007-2014 Chevy Silverado 2500 HD / 3500 HD

2007-2014 GMC Sierra 2500 HD / 3500 HD

NOT for 2007 Classic model

Specifics and Features:

Single-side adhesive, easy for you to replace burn out bulb in the future

Foam seal, thicker EVA foam can provide excellent waterproof performance

High quality material, not easy to be worn out and can be used for long time normally

Easy to install, no modification or trimming needed

Tips:

Make sure the surface of both vehicle body and brake light is clean before installation

Check where the leak come from, you'd better add some clear sealant on the screw head of light, perhaps the water get in through there.


Michael
Reviewed in the United States on January 7, 2025
Fit perfect
PEARL M OVERHILL
Reviewed in Canada on July 28, 2024
I have a 2012 Silverado, this did not fit properly. Wish I would have read more reviews on similar trucks
XsTatiC
Reviewed in Canada on February 8, 2024
Didn't fit. Left an obvious gap that's worse than it was before. Not sure what was up, but definitely not meant for the light on my 2007 GMC Sierra Classic. The most difficult part was getting the old gasket off and cleaning the surface. Install was simply peel and stick, but, yeah... for another light than mine I guess.Off to the GM dealership since it's supposed to rain tomorrow.
"Trini Ricky"
Reviewed in Canada on October 1, 2024
Poor fit on OEM light
Lammy
Reviewed in Canada on September 1, 2023
Not sure how they designed this but as you can see in the picture the new gasket (top) is different from the factory gasket (bottom). It’s wider and has vertical dividers that line up with nothing. Had to trim to fit by removing the dividers, shortening the width and trimming the ends which were too wide and then siliconed the top after installed. Terrible. Go back to the drawing board people.
Nicole F
Reviewed in Canada on August 6, 2023
Tried to install on a 2008 Silverado 2500HD. The design of the gasket is different than the stock one. It goes around the entire lamp and seals off the screw holes which is good in theory. However there are channels that it goes over and it creates bumps. I took a dremel and ground away these channels and the gasket now sat flat across the entire surface.Upon installation there was a 1/8"-3/16" gap/opening in the middle on the top and no amount of tightening the screws was going to fix this. The foam is too dense to allow it to seal evenly and this is probably the reason why the OEM one is so soft.In the end I just sealed it with silicone, done! Do the same...
James M.
Reviewed in Canada on July 14, 2023
Have not had a leak since installing this.
Eric
Reviewed in the United States on February 27, 2023
Lasted 2 hours leaks worse then the original one from 1999 in 5 minutes filled up half a 16 oz water bottle from just one of the 3 leaks I now have a 3 gallon pot to collect the water sitting I’m my truck
Harrison Blankenship
Reviewed in the United States on November 27, 2023
Works as it should, sealed off easy install and no more leaks!
Heriberto R.
Reviewed in the United States on October 5, 2023
I found the brake light gasket seal I bought to be quite good, especially given how cheap it was. It might not be as high-end as other more expensive choices, but it adequately sealed the brake light assembly to keep moisture and debris out. My brake lights stayed functional and protected because of their simple installation and good fit. It provided dependable performance for the price, and I was pleased with the benefit it provided in protecting the lighting system in my truck.
Thomas
Reviewed in Canada on July 26, 2021
These DO NOT directly replace the factory seal, I used these in addition the the leaking factory seal hoping it will stopI will be buying an OEM seal to replaceI’m pretty disappointed
Greg
Reviewed in Canada on October 28, 2021
Fit my 03 Silverado but had to trim gasket Tabs slightly. Truck has been outside for several rainy days and no leaks. Hopefully it holds up over time.
Kathy
Reviewed in the United States on November 19, 2019
I have a 2002 GMC Sierra 2500HD and this gasket wasn't 100% the right fit. The perimeter lines up for the most part, but there are a few random "tabs" of the inner gasket, that stick in awkward spots. They look like they shouldn't be there, no matter which way you adhere the gasket. There is no spot on the lens cover for them to sit and they throw off the alignment of the gasket. I am skeptical that this will work and have a feeling I will have to purchase another model shortly. I will update again in due time.*Update 12/26/19* This seller went out of their way to contact me directly to apologize about the issue. They were grateful that I pointed out the flaw, and will use my feedback to work on correcting he issue. In addition, they issued me a full refund. Lastly, it has been a few weeks since I ordered this piece and there have been a few rain/snow events. The gasket hasn't leaked either. I have changed my rating of this seller/product, to reflect my new perspective.
Recommended Products